PHOTO COUPLER RECEIVER MODULE TRANSMITTING RECEIVER
RECEIVER MODULE
 
HOW TO USE INVISIBLE PRODUCTS
SOLDERING:
1. Soldering Bath -- 260℃±5℃ within 5 seconds.(Dip depth should under 1/16 inch below seating plane)
2. Soldering Iron Under 40W within 3 seconds. (Tip temperature:380+-5℃)
3. The neutrality flux be used before soldering
CLEANING:
1. Do not use unspecified chemical liquid to clean invisible product. They could harm the invisible product. If cleaning is necessary, wipe the pin out with alcohol. Freon TE or Chlorosen at normal temperature for less Than 1 minute. Or wipe the surface with alcohol. When other chemical solutions mot specified is used. It may cause crack or haze on the surface of the Invisible product
PREVENTING OVER CURRENT:
1. Be not over current.
2. In order to operate BRIGHT INVISIBLE PRODUCTS under stable conditions. Put protective resistors in series. Resistor values can be determined by supplying voltage or current is in the invisible product. Recommended current is in the range of forward current 50mA
3. Circuit must be designed so that over voltage (over current) is not applied to the invisible product during on/off switching. Transient or pulse current will damage the junction of invisible product die.
BRIGHTNESS:
1. For obtaining even brightness. Each segment should be at the same current. So the best circuit design is to supply constant current for each segment
2. To increase brightness. Increase current. But do not over maximum rating.
3. To check the appearance defect of invisible product. The viewing distance should be 15cm minimum.
4. For obtaining more uniform brightness on SIDE LOOK and INTERRUPTER. The supplying forward current should be over 20mA , but do not be over rating.

 
QUALITY CONTROL AND ASSURANCE
CLASSIFICATION TEST ITEM DESCRIPTION AND TEST CONDITION REFERENCE STANDARD
ENDURANCE
TEST
OPERATION LIFE Ta: 25 ℃ + -5 ℃ Side look : IR:IF=20mA ; End look :IR:IF=50mA ; Vce =5v Time:1000hr MIL-STD-883E:1016
HIGH TEMPERATURE HIGH HUMIDITY STORAGE Ta: 65 ℃ + -5 ℃ RH:90% -95% Time: 240hrs MIL-STD-883E:1004.7 MIL-STD -202F :103B
HIGH TEMPERATURE STORAGE Ta: 125 ℃ + - 5 ℃ Time: 240hrs MIL-STD-883E:1008. 2
LOW TEMPERATURE STORAGE Ta: -55 ℃ + -5 ℃ Time: 240s+- 2hrs JIS-C-7021:B-12
ENVIRONMENTAL
TEST
TEMPERATURE CYCLING Ta: -55 ℃ + - 5 ℃ (30min)~25+ -5 ℃ (5min)~ 85 ℃ + -5 ℃ (30min)~25+ -5 ℃ (5min)10cycle MIL-STD-883E:1010.7
THERMAL SHOCK Ta: -55 ℃ + -5 ℃ (10min)~ 125 ℃ + -5 ℃ (10min)15cycle MIL-STD-883E:1011.9
MIL-STD -202F : 107G
SOLDER RESISTANCE To evaluate resistance of thermal stress caused by soldering Ta:260+ - 5 ℃ Time:10+ - 2 sec MIL-STD -202F :210B
SOLDERABILITY To evaluate solder ability on leads of device Ta:245+ - 5 ℃ Time:5+ - 0.5 sec MIL-STD-883E:2003.7 MIL-STD -202F : 208F 1

 
SELECTION GUIDE (PART NO. SYSTEM)

 
PACKAGE TYPE:
1 : Small size standard side vrew (Molding type)
4 : Standard view (Encapsulate type)
5 : Large size Encape type
6 : Mini size SMD type
Ic Type
Supply Voltage:
0:Vcc=5.0V
1:Vcc=3.0V
2:Vcc=2.4V


   
BPF CENTER FREQUENCYL:
0:38.0KHz
1:32.7KHz
2:40.0KHz
3:56.0KHz
4:3.67KHz
PIN FUNCTIONS
SHIELDING TYPE
SPECIAL DEVICE
-FBxx:Forming Bent from stopper
-LCxx:Short feet

 
裕挺企業股份有限公司   111臺北市士林區延平北路7段27巷25弄5號
電話:02-2810-9858   傳真:02-2810-9119   E-mail:七乐彩中奖奖金表
 
Copyright © 2007 Anole enterprise Co., Ltd. All Rights Reserved. Design by T.S.G.